Alekseev, Vyacheslav P.

2025

• 1 Kurkin E., Kishov E., Chertykovtseva V. etc. Bimaterial topology optimization for Ti-6Al-4V lattice bushing design in PA6 injection molded structures // Journal of Manufacturing Processes 2025. — Vol. 141. — P. 1368-1384
• 2 Agapovichev A.V., Khaimovich A.I., Smelov V.G. etc. Optimization of L-PBF Process Parameters for Defect Reduction and Mechanical Strength of Ni-Cr-Mo-Nb Superalloy Using Multi-Objective Methods // Materials 2025. — Vol. 18. Issue 8. № 8.
• 3 Khaimovich A.I., Smelov V.G., Kokareva V.V. etc. Optimization of L-PBF Process Parameters: A Multi-Objective Framework for Variance Reduction and Mechanical Strength Enhancement Using Linear Programming and Multi-Objective Methods // Metals 2025. — Vol. 15. Issue 9. № 9.
• 4 Khaimovich A.I., Alekseev V.P., Smelov V.G. etc. Investigation of the Variability of Additive Manufacturing on Special Curved Comb-Type Specimens // Russian Engineering Research 2025. — Vol. 45. Issue 11. № 11. — P. 1577-1582

2024

• 1 Sedelnikov A., Kurkin E., Smelov V. etc. Short Fiber-Reinforced Polymer Polyamide 6 Lugs and Selective Laser-Melted Ti-6Al-4V Bushing Contact Cohesive Zone Model Mode II Parameters’ Evaluation // Computation 2024. — Vol. 12. Issue 5. № 5.
• 2 Alekseev V.P., Khaimovich A.I., Smelov V.G. etc. Testing a Statistical Quality Control Method Based on Short-Run Control Charts for Small Batch Production on the Example of Selective Laser Sintering of Blanks of Gas Turbine Engine Blades // Russian Engineering Research 2024. — Vol. 44. Issue 11. № 11. — P. 1623-1628
• 3 Alekseev V.P., Khaimovich A.I., Smelov V.G. etc. Development of Modified Short-Run Target Control Charts and Determination of Capability Indices for Analysis of Controllability of Small Batch Production Processes // Russian Engineering Research 2024. — Vol. 44. Issue 11. № 11. — P. 1608-1612

2021

• 1 Agapovichev Anton Vasilevich, Kokareva V.V., Alekseev V.P. etc. Исследование структуры и механических свойств образцов, полученных по технологии селективного лазерного легирования из порошка жаропрочного сплава Inconel 738 // Chernye Metally 2021. — № 1. — P. 67-71
• 2 Agapovichev A.V., Kokareva V.V., Alekseev V.P. etc. Study of the structure and mechanical properties of samples obtained by the selective laser alloying technology from the inconel 738 heat-resistant alloy powder // Chernye Metally 2021. — Vol. 2021. Issue 1. — P. 67-71

2019

• 1 Nosova E., Baliakin A., Galkina N. etc. Research of Titanium Covering Effect Received by Selective Laser Melting on Mechanical Properties of Aluminum Alloy Al-6Mg // Materials Today: Proceedings. — 2019. — Vol. 11. — P. 370-374

2018

• 1 Agapovichev A.V., Sotov A.V., Kyarimov R.R. etc. The investigation of microstructure and mechanical properties of tool steel produced by selective laser melting technology // IOP Conference Series: Materials Science and Engineering. — 2018. — Vol. 441. Issue 1.
• 2 Kharchenko I., Panchenko A., Kharchenko A. etc. Modeling of structuring processes at hardening of expanding cements and concretes on their basis // MATEC Web of Conferences. — 2018. — Vol. 196.
• 3 Balyakin A.V., Dobryshkina E.M., Vdovin R.A. etc. Rapid Prototyping Technology for Manufacturing GTE Turbine Blades // IOP Conference Series: Materials Science and Engineering. — 2018. — Vol. 327. Issue 2.
• 4 Alekseev V., Harchenko I., Harchenko A. etc. About the influence of hardening conditions on the structure and properties of expansive concretes // MATEC Web of Conferences. — 2018. — Vol. 193.

2017

• 1 Ponyatov D.S., Alekseev V.P., Khaimovich A.I. The study of the process of chip segmentation in case of edge cutting machining of titanium alloy // MATEC Web of Conferences. — 2017. — Vol. 129.
• 2 Alexeev V.P., Balyakin A.V., Khaimovich A.I. Influence of the direction of selective laser sintering on machinability of parts from 316L steel // IOP Conference Series: Materials Science and Engineering. — 2017. — Vol. 177. Issue 1.

2016

• 1 Balyakin A., Dobryshkina E.M., Vdovin R. etc. Исследование применения технологий быстрого прототипирования для изготовления лопаток турбины ГТД // Известия Самарского научного центра РАН 2016. — Vol. 18. № 4-6. — P. 1168-1172
• 2 Alekseev V.P., Khaimovich A.I. Testing criterion models of destruction of materials with different rheological properties under edge cutting machining // Key Engineering Materials. — 2016. — Vol. 684. — P. 13-20