федеральное государственное автономное образовательное учреждение высшего образования
«Самарский национальный исследовательский университет имени академика С.П. Королева»

Alekseev, Vyacheslav P.

  • Department of Engine Production Technology, senior Lecturer
  • researcher
  • engineer
  • Department of Aircraft Construction and Design, engineer
2024
  • 1 Sedelnikov A., Kurkin E., Smelov V. etc. Short Fiber-Reinforced Polymer Polyamide 6 Lugs and Selective Laser-Melted Ti-6Al-4V Bushing Contact Cohesive Zone Model Mode II Parameters’ Evaluation // Computation 2024. — Vol. 12. Issue 5. № 5.
2021
  • 1 Agapovichev A.V., Kokareva V.V., Alekseev V.P. etc. Исследование структуры и механических свойств образцов, полученных по технологии селективного лазерного легирования из порошка жаропрочного сплава Inconel 738 // Chernye Metally 2021. — № 1. — P. 67-71
  • 2 Agapovichev A.V., Kokareva V.V., Alekseev V.P. etc. Study of the structure and mechanical properties of samples obtained by the selective laser alloying technology from the inconel 738 heat-resistant alloy powder // Chernye Metally 2021. — Vol. 2021. Issue 1. — P. 67-71
2019
  • 1 Nosova E., Baliakin A., Galkina N. etc. Research of Titanium Covering Effect Received by Selective Laser Melting on Mechanical Properties of Aluminum Alloy Al-6Mg // Materials Today: Proceedings. — 2019. — Vol. 11. — P. 370-374
2018
  • 1 Kharchenko I., Panchenko A., Kharchenko A. etc. Modeling of structuring processes at hardening of expanding cements and concretes on their basis // MATEC Web of Conferences. — 2018. — Vol. 196.
  • 2 Alekseev V., Harchenko I., Harchenko A. etc. About the influence of hardening conditions on the structure and properties of expansive concretes // MATEC Web of Conferences. — 2018. — Vol. 193.
  • 3 Balyakin A.V., Bezsonova E. M. , Vdovin R.A. etc. Rapid Prototyping Technology for Manufacturing GTE Turbine Blades // IOP Conference Series: Materials Science and Engineering. — 2018. — Vol. 327. Issue 2.
  • 4 Agapovichev A. V. , Sotov A. V. , Kyarimov R. R. etc. The investigation of microstructure and mechanical properties of tool steel produced by selective laser melting technology // IOP Conference Series: Materials Science and Engineering. — 2018. — Vol. 441. Issue 1.
2017
  • 1 Ponyatov D.S., Alekseev V.P., Khaimovich A.I. The study of the process of chip segmentation in case of edge cutting machining of titanium alloy // MATEC Web of Conferences. — 2017. — Vol. 129.
  • 2 Alexeev V.P., Balyakin A.V., Khaimovich A.I. Influence of the direction of selective laser sintering on machinability of parts from 316L steel // IOP Conference Series: Materials Science and Engineering. — 2017. — Vol. 177. Issue 1.
2016
  • 1 Alekseev V.P., Khaimovich A.I. Testing criterion models of destruction of materials with different rheological properties under edge cutting machining // Key Engineering Materials. — 2016. — Vol. 684. — P. 13-20
  • 2 Balyakin A., Dobryshkina E.M., Vdovin R. etc. Исследование применения технологий быстрого прототипирования для изготовления лопаток турбины ГТД // Известия Самарского научного центра РАН 2016. — Vol. 18. № 4-6. — P. 1168-1172